I can only cut and/or polish virtually all types of agate, jasper (including picture jasper), obsidian, petrified wood, thundereggs, and closely related rocks. In other words there is quartz in it. ALL crystals, river rocks, limestone, rocks that look like they belong in driveways, marble, granite, are just some of the types that I can't polish. I can't cut anything less than 2 inches in diameter. I get asked about these rock types at least once a week. You're wasting you time asking of I can cut and/or polish them. Really soft jasper won't polish and I usually won't cut it because it turns the oil in my saws to mud. Anything soft enough to turn into powder or chip like crazy when you whack it with a hammer is none of these (except for obsidian). I don't want to waste your money on rocks that will look ugly :) Also, and this is very important, my saws can handle anything from about 2 1/2" to to 10" I will send them back, on your nickle, if I can't do anything with any of them.
It will help greatly if you take photos of your pieces if there is any doubt; they are always good to have anyway so there is no misunderstanding of what I can or can't do. If you send something I can't do anything with after I get all the info from you then I will charge for shipping it back, unless there is a huge misunderstanding or a mistake on my part.
Please read this 3 times! I can cut pieces anywhere from 2-1/2 inches across to around 10" in the smallest cross section. I can cut them in half or slab to any thickness you want. I can polish anything with a flat cut surface, up to about 7" across the longest side. I will cut it for you if it isn't cut already. I can't polish anything that isn't sliced on a rock saw, or obsidian (it's just too much agony to get it scratch free). Slabs that are 1/2" or thicker are OK too (nothing thinner please). The equipment I use results in a very flat, very highly polished surface on most types of rock. Almost all rocks cut with a tile saw without a vise will NOT be suitable for polishing unless I cut the face off. Same goes for saws that are misaligned or have a worn blade. If it is a very rough surface, has grooves, chips, and/or isn't flat I will recut it first. If I can't then I will send it back.
Turnaround time typically varies from a week for small jobs to 4-6 weeks for a big box o' rocks, depending on how much other work I have lined up. If I have free time I can occasionally get to your rocks right away. You can bring them here (Oregon City OR) or mail them. Depending on where you are, USPS rates are generally $9-$12 for up to 2 or 3 pounds, heavier than that, flat rate Priority Mail is almost always cheapest. A flate rate padded envelope $9.10) can hold up to around 5 pounds, medium flat rate box ($15.50) can hold up to about 15 pounds (which is packing them in tight) a large flat rate box ($20.65) can hold up to about 25 pounds. Pack cut rocks and slabs in tight and in bubble wrap, if it chips in shipping it may be unusable or need to be cut again. Pack uncut rocks wrapped in newspaper etc. in tight, if they roll around and hit each other they're likely to get damaged. The postal service seems to think that everything even a little heavy needs to be thrown off a roof!
My rates are: My minumin charge is $5.00. (which will be applied to the total if it comes out to more than $5.00 so it's not a separate fee). For slabbing or cutting in half (no polishing) is $0.50 per square inch (for example a 4" by 4" square shaped piece is a maximum charge of $8; it's always less if not a perfect square or rectangle). Both side count for cutting a rock in half. For taking multiple slabs from a piece, I charge for one side. Add an additional $0.40 per square inch for polishing. So slabbing and polishing both sides of a piece would amount to $0.80 per square inch. If you send me cut rocks with a flat smooth surface the rate for polishing is 90 cents per square inch. Rough or not perfectly flat faces will have to be cut again.
PS. I won't cut Polka Dot mine thundereggs, the matrix is too soft and makes a muddy mess out of my saw oil, and they have the nasy habit of breaking in the saw which can ruin my blade!
If this sounds draconian, it's because it is. I don't want to waste your or my precious time.
Please Read: I am usually backed up / busy with something, so I may not get to your rocks for a week or more. Some people seem to think I can get it done overnight and that simply isn't feasible in most cases. If you bring a small rock or 2 here (Oregon City OR) and I happen to have some free time I can cut it while you wait.
OreRockOn Rock Dig Locations DVD NEW VERSION 8!
Lapidary Materials, Faceting Rough, Fossils, and More for Sale
Obsidian for Knappers and Obsidian Needles for Sale
!ONE TIME ONLY SPECIAL! HOLLEY BLUE Agate For Sale!
Lapidary Equipment Restoration Services
Lapidary Arts Instruction Classes
Polished Rock Slabs & Pieces for Sale
Polished Agates for Sale
Polished Thundereggs for Sale
Faceted Gemstones for sale
Fossils for Sale
Cabochons for Sale
Rock Crystal Geodes for Sale
Rock Display Stands for Sale
Rock & Lapidary Bookstore
Ore-Rock-On Rockhound and Lapidary Supply Store
Back to
Ore-Rock-On!
Copyright © 1997 - 2023
Tim FisherUsers may download this World Wide Web page for personal use only. Unauthorized copying or distribution of this page or any of its contents without the express permission of the author is expressly forbidden.